SONOFF Basic R2 10A Smart WiFi Wireless Light Switch, Universal DIY Module for Smart Home Automation Solution, Works with Amazon Alexa & Google Home, Compatible with IFTTT, No Hub Required

Product Information

The switch for the first channel, active low. APP configuration pin, when the low level> 5S, enter the pairing mode. SONOFF SV is a low voltage switch. The low voltage light switch supports 5-24V power supply. Power supply separation enables it to control both AC and DC power, although some welding is required for this purpose. It has GIPO reserved to support secondary development. This product does not have 433 RF function and shell.

Chip enable terminal high level: valid; low level: closed.Note: An external pull-up resistor of 1~10K, connect a 100nF capacitor to the ground.This item works with Alexa and Google Assistant, and the manufacturer has their own app to control this system. The 40039 is a single channel Wi-Fi relay switch receiver. Part of the Culina Konect system from Forum Lighting. This a completely wireless switching system converts the kinetic energy produced by physically switching the switch into electrical energy to control your lights via remote switch and receiver. The flashing of the Wi-Fi status light is in a cycle of 2 seconds, as shown in the figure, the low-level light is on and the high-level light is off. Detailed explanation of each status: The relay switch for the first channel: active high, power-on default low level. Note: As a switch button, there will be a period of high level at the moment of power-on, which requires a pull-down (1~4.7K) resistor to ground. The flashing mode of the Wi-Fi status light on the device represents the its current network working status. The specific status includes the following seven types:

Normal: The device is working normally and the connection to the cloud server is normal.The device can be only controlled through the APP in this mode. Strong signal up to 40m range outdoors, 15m indoors for plasterboard, 8m indoors for concrete or glass The Gateway acts as a conduit for any RF Quinetic products to be linked together thus creating a hybrid system for both RF and WiFi connectivity. Power-on status configuration: The power-on switch status can be configured on or off through the APP, and the default power-on status is off.SONOFF SV low voltage wireless remote switch makes all home appliances smart. As long as the mobile has network, customers can remotely control the appliances by turning them on off from anywhere at any time. Another feature available is to set timing schedules for the appliances, which can include countdown, scheduled on/off, and can thus, help customers maintain an easy life. Place the module’s power supply (VCC) pin capacitance and other module pin capacitances, resistors as close as possible to the module pins, and the tracepath should be short. Count downtimer: The count down is to facilitate the user to perform one-time timing operations, such as turn on/off the device after 30 minutes. It is very convenient to turn off a device after running a period of time. This device supports up to 24 hours of count down. The device obtains information in different ways in the two modes, read below section for details. 4.3 The Wi-Fi module basic workflow PSF-B04 supports timer. The eWeLink APP provides four timing modes to facilitate the use in more scenarios.

The switch for the third channel, active low. APP configuration pin, when the low level> 5S, enter the pairing mode. The switch for the second channel, active low. APP configuration pin, when the low level> 5S, enter the pairing mode.

The upper and lower layers of the PCB where the module is placed should not be routed as much as possible. Do the copper-clad processing, and the PCB from the module antenna to the nearest pin of the module should be hollowed out as much as possible. PSF-B04 module can be used as a 4-channel switch, which can control the switch locally or remotely through APP. The switch for the fourth channel pin, active low. APP configuration pin, when the low level> 5S, enter the pairing mode.

Main switch for 4-channel pin, active low. APP configuration pin, when the low level> 5S, enter the pairing mode. The timer function is configured through the APP, and the timer is divided into the following four types: External reset signal: active at low level, externally need to pull up a 10K resistor to 3.3V, and connect a 100nF capacitor to ground. This item is suitable for use with single, double and triple kinetic switches plus a single switch key fob. WiFi and RF Wireless Receiver Non-Dimmable in Matt White - Specs The module PCB antenna area and the 15 mm extension area need to be clear (copper, trace on the board, and component placement are strictly prohibited), refer to the following figure:The relay switch for the fourth channel, active low. APP configuration pin, when the low level> 5S, enter the pairing mode. Note: The chip configuration pin needs to pull down (1~4.7K) resistor to ground. No Server: The device has been connected to the router, but it cannot connect to the server (also known as”cannot access the Internet”). The compact design means it can be installed almost anywhere. It has a range of up to 40m from the switch when outside, or 8m away when indoors and can be controlled not only by the switches.